Try Not To Disassemble What’s Not Necessary Some manufacturers provide disassembly instructions which can be helpful when taking your chair apart. If your chair arrived fully assembled, you will need to figure out what you can and cannot remove so you don’t damage your chair. This means you will most likely have to remove the chair from the cylinder in order to disassemble it. Other chairs arrive only needing to add the cylinder to the base, and the chair onto the cylinder and base. Some office chairs come in multiple pieces, which means you can most likely disassemble the chair in the opposite order of assembly. 7 Things To Consider When Disassembling An Office Chair Remember How The Chair Cameīefore disassembling your office chair, it may be helpful to remember how your chair arrived. To remove the casters, place the base upside down with the casters facing up. You shouldn’t have to remove casters unless you need to for replacement or a return. Most casters on office chairs are just popped right into the base. Tap sides of the cylinder if it is really stuck.ĥ. Use the rubber mallet to dislodge the cylinder from the base. Stand back so the cylinder doesn’t hit your feet. Don’t forget to protect your surface and floor. To remove the cylinder from the base, you’ll need to use a rubber mallet. Cylinders do not screw on, so loosen it until you can pull it from the mechanism. Once tight to the cylinder, turn the pipe wrench a quarter turn or until it comes loose. Using the pipe wrench, clamp down on the cylinder near the bottom of the mechanism. To get good grip and to protect the cylinder, add duct tape to the teeth of the pipe wrench. Before you start, be sure to protect your table’s surface and the floor. To remove the cylinder, you’ll need a large pipe wrench. How To Disassemble Office Chair Cylinder and Baseīefore you remove the cylinder, remember that it can easily be damaged when trying to remove it. Some chairs you can easily remove the armrest by pulling them out of the slot underneath the chair while activating the adjustment lever.Ĥ. Place all hardware in a bag and keep it with the chair. Start by removing the bolts from the chair with an Allen wrench or screwdriver. Armrest can contain multiple parts, so it is best to remember the order in which you are talking them off of the chair. How To Disassemble Office Chair ArmrestsĪrmrests only need to removed if absolutely necessary. Once all screws and/or washer are removed from the chair, place them into a bag so you don’t lose them and keep it with the chair. To remove the backrest, use an Allen wrench or screw driver to remove the bolts underneath the chair that are holding the backrest in place. On some office chairs this will not be able to be removed because the backrest is attached to the frame, such as the Steelcase Leap. How To Disassemble Office Chair Backrestįor most office chairs, you should be able to easily remove the backrest because they are attached with bolts at the back of the chair. Don’t forget to put all small, loose parts into a bag for safe keeping. After the headrest is removed, place the cover plate or tabs back onto the chair. Once those are removed, using a screwdriver or Allen wrench, remove all bolts from the headrest. To remove the headrest from your chair, first see if you need to remove a cover plate, or tabs. Most headrests on office chairs are attached with a few bolts. Contact the chair manufacturer with any questions or concerns regarding the disassembly of your office chair. Note that with some chairs, you may not be able to remove certain parts if they arrived already fully attached to the frame. To help you with disassembling your chair, I will go through each part on an office chair and demonstrate the general instructions for disassembly. As previously stated, follow the original assembly instructions if your chair came with any. No matter what reason you have for disassembling your office chair, you must be careful so you don’t damage your chair. Seven Things To Consider When Disassembling an Office Chair.How To Remove Office Chair Cylinder and Base.Who is and The Learning Center? How To Disassemble An Office Chair To learn more about the products we sell, our review process and why you can trust us, please visit: Why we’re different. Full Disclaimer: We are an office furniture dealer and sell some of the products we review.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |